I can't get mine to power off instantly at the switch either but here's a software solution. Go...

Ernie

07-03-2003 03:16 AM
Ernie

Hi all is this function available on this mobo? The wol connector is missing (even if on PCB pads are present) but i hope that with internal LAN it...

Slang

07-02-2003 09:13 PM
Slang

Yeah it was years ago, with EDO ram, now you can put together sticks of different size "DH" <rchngroups (AT) mindspring (DOT) com> a écrit dans le...

DH

07-02-2003 04:24 PM
Nicolas GIF

I have 2 K7S5A pro systems from Fry's and either one would even POST. The first one I got Booted and installed WinXP, but then suddently it won't...

tojo

07-02-2003 10:45 AM
jaster

I bought this MB around December 2001. The Version is assumed to be V3.1 (printed on top LHS corner). I downloaded the newest BIOS...

Sam Cheung

07-01-2003 06:32 PM
Buffalo

I went back into bios and made sure these were enabled, but Im still not getting any parallel port or usb. what else can i do to get these to...

muggle

07-01-2003 02:17 PM
The TweakOholic

Thanks for the tip, I bought the same modem at Fry's for $15 w/$10 rebate Sat. but the rebate form doesn't have the 3652 listed. I'll probably take...

Steve Weldon

06-30-2003 06:53 PM
Steve Weldon

I have switched motherboards with no problems at all and i switched from mso mobos to the k series and gigabytes. i also have put my HD into a few...

Yomper

06-30-2003 05:20 PM
Shep©

Fry's has the AMD XP2400+ and ecs k7s5a pro motherboard for $89. What is the minimum power supply that will work with this combo assuming nothing...

JimL

06-30-2003 02:54 PM
Shep©

Will I get noticably better performance using DDR memory instead of PC133 memory, Basically is it worth the extra cost to upgrade from PC133...

Joe Murphy

06-29-2003 01:54 PM
Shep©

I am looking into my sister's machine. The power LED is now blinking all the time. Any idea on what is causing this? I replaced the battery because...

Jeff Finnan

06-28-2003 08:48 PM
Jeff Finnan

Has anyone had any luck running a 333 mhz bus cpu on a rev 3.1 K7S5a? I can get a good deal on a 2700+ cpu, but it has the 333 mhz bus, and...

Brian Campbell

06-28-2003 03:09 PM
Shep©

I will second that. I have 1209 running on my Pro board. XP 1800 oced to 2100. It is extremely stable. "Shep©" <shep (AT) gmx (DOT) co.uk> wrote

SPS 700

06-27-2003 07:40 PM
John D.

I run it with win2k3 and it works fine on my k7s5a mobo. Beacon "xxx73" <xxx73 (AT) mailandnews (DOT) com> wrote

beacon

06-27-2003 07:15 PM
beacon

I have three ECS K75SA and one Pro board. All are running Honey X bios and all are overclocked with various degrees of sucess dependimg on memory...

SPS 700

06-26-2003 10:19 PM
SPS 700

"Wolfram Nickl" <wolfram_nickl (AT) hotmail (DOT) com> wrote Have you tried each stick of RAM separately to determine if one of them is bad? If...

WROSIE

06-26-2003 02:57 PM
Shep©

due to costs i was going hard cable route. laptop has built in 10/100 and desktop has pci 10/100. cable modem has both rj45 and usb. using usb...

Deathwalker

06-25-2003 10:47 PM
Frank

I just got a Maxtor 160 with an included ATA/133 card. I used the ATA/133 card and partitioned the drive (less time to defrag the smaller...

WROSIE

06-25-2003 07:22 PM
Les Caudle

Hey I have a P4S5A/DX+ motherboard and I would like to know if the motherboard supports fan control. The reason I am asking is that it never seems...

news.inet.tele.dk

06-25-2003 03:48 PM
news.inet.tele.dk

What rookie, how in the world can he install motherboard drivers when he can't get past partitioning? 1. Quit using that partition program. 2. I...

woody

06-24-2003 11:24 PM
mrhandi

aa356 (AT) chebucto (DOT) ns.ca (Brian Campbell) wrote in message news:<bcrvde$374$2 (AT) News (DOT) Dal.Ca>... Thanks -- no the pinouts on the card...

John Armstrong

06-24-2003 10:47 PM
John Armstrong

I have a P4VXASD2+ mb with a Celeron 1.6. What kind of improvement can I expect if I change to an Intel 2.4. Yes it is a Fry's deal. The Celeron...

Brian Cahill

06-24-2003 06:27 AM
Pip

Here's a rough guide to psu consumption I made from either Andatech or Tomshardware sites. The -3.3, -5 and -12 don't count for modern ATX...

John Smith

06-24-2003 12:37 AM
jaster

Li'l ol' me wrote : Well you can get the manual at ftp://ftp.pcchips.com.tw/manual/m810/810s50.zip, if you need it. Page 17 gives front panel...

Pip

06-23-2003 05:09 PM
Li'l ol' me

what would happen if i put a 333mhz fsb athlon in a 266mhz fsb motherboard thanks

Dits

06-23-2003 03:41 PM
Pip

yes and no: I have tried 2400+ on some 4 different K7SEM boards and no: It always ends up locking the system. Michael W. "Michael Swanson"...

Michael Wechter

06-23-2003 02:03 PM
Michael Wechter

I have been trained by the Navy and the Air Force in micro soldering techniques and I agree, for most through the hole type jobs a plain old solder...

bitsbucket

06-23-2003 02:29 AM
bitsbucket

"Mr. Slow" <millenniumgoldspammersarebastards_ (AT) crouchvale (DOT) freeserve.co.uk> wrote D'oh. It somehow got set to 133/166 -- someone pressed...

Dennis Wilson

06-22-2003 06:26 PM
Mr. Slow