I setup an IBM 300PL with Suse Linux 10.0, everything works fine with the
onboard-graphics-adapter. When I add a PCI-graphics-adapter I have no
chance to configure X, the monitor gets black. This TNT2 works fine in an
other pc.

Any ideas? Especially I think, I could try some sax2-options, -d 0 and -d 1
didn't help, as well as starting without framebuffer.

Here are some technical data:

Interrupts:
CPU0
0: 240027 XT-PIC timer
1: 10 XT-PIC i8042
2: 0 XT-PIC cascade
5: 1 XT-PIC CS4231
7: 3 XT-PIC parport0
8: 3 XT-PIC rtc
9: 0 XT-PIC acpi
11: 12358 XT-PIC uhci_hcd:usb1, eth0
12: 127 XT-PIC i8042
14: 10781 XT-PIC ide0
15: 42817 XT-PIC ide1
NMI: 0
LOC: 0
ERR: 2
MIS: 0


hwinfo --gfxcard
17: PCI 14.0: 0300 VGA compatible controller (VGA)
[Created at pci.277]
UDI: /org/freedesktop/Hal/devices/pci_10de_2d
SysFS ID: /devices/pci0000:00/0000:00:14.0
SysFS BusID: 0000:00:14.0
Hardware Class: graphics card
Model: "Creative RIVA TNT2 Model 64/Model 64 Pro"
Vendor: pci 0x10de "nVidia Corporation"
Device: pci 0x002d "RIVA TNT2 Model 64/Model 64 Pro"
SubVendor: pci 0x1102 "Creative Labs"
SubDevice: pci 0x1046
Revision: 0x15
Memory Range: 0xf3000000-0xf3ffffff (rw,non-prefetchable)
Memory Range: 0xf0000000-0xf1ffffff (rw,prefetchable)
Memory Range: 0x14100000-0x1410ffff (ro,prefetchable,disabled)
IRQ: 255 (no events)
I/O Ports: 0x3c0-0x3df (rw)
Module Alias: "pci:v000010DEd0000002Dsv00001102sd00001046bc03sc0 0i00"
Driver Info #0:
XFree86 v4 Server Module: nv
Config Status: cfg=yes, avail=yes, need=yes, active=unknown

18: PCI 101.0: 0300 VGA compatible controller (VGA)
[Created at pci.277]
UDI: /org/freedesktop/Hal/devices/pci_5333_8904
Parent ID: vSkL.+oqW+GBE7wA
SysFS ID: /devices/pci0000:00/0000:00:01.0/0000:01:01.0
SysFS BusID: 0000:01:01.0
Hardware Class: graphics card
Model: "S3 Integrated Trio3D"
Vendor: pci 0x5333 "S3 Inc."
Device: pci 0x8904 "Integrated Trio3D"
Revision: 0x01
Memory Range: 0xf4000000-0xf7ffffff (rw,non-prefetchable,disabled)
Memory Range: 0x14000000-0x1400ffff (ro,prefetchable,disabled)
Module Alias: "pci:v00005333d00008904sv00000000sd00000000bc03sc0 0i00"
Driver Info #0:
XFree86 v4 Server Module: s3virge
Config Status: cfg=yes, avail=yes, need=yes, active=unknown
Attached to: #11 (PCI bridge)

Primary display adapter: #17



00:14.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2
Model
64/Model 64 Pro] (rev 15)
01:01.0 VGA compatible controller: S3 Inc. Trio 64 3D (rev 01)




00:14.0 VGA compatible controller: nVidia Corporation NV5M64 [RIVA TNT2
Model
64/Model 64 Pro] (rev 15) (prog-if 00 [VGA])
Subsystem: Creative Labs: Unknown device 1046
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Latency: 40 (1250ns min, 250ns max)
Interrupt: pin A routed to IRQ 255
Region 0: Memory at f3000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at f0000000 (32-bit, prefetchable) [size=32M]
[virtual] Expansion ROM at 14100000 [disabled] [size=64K]
Capabilities: [60] Power Management version 1
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:01.0 VGA compatible controller: S3 Inc. Trio 64 3D (rev 01) (prog-if 00
[VGA])
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping-
SERR- FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
<TAbort-
<MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 0
Region 0: Memory at f4000000 (32-bit, non-prefetchable) [disabled]
[size=64M]
Expansion ROM at 14000000 [disabled] [size=64K]
Capabilities: [44] Power Management version 1
Flags: PMEClk- DSI+ D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-





3Ddiag version 0.728
Verifying 3D configuration:
Using 3dinfo
************************************************** **********

================================================== ==============
No 3D capable graphic chipset found!
================================================== ==============

Checking GL/GLU/glut runtime configuration:
GL/GLU ... done (package xorg-x11-Mesa)
glut ... done (package freeglut)



cpu:
Pentium II (Deschutes), 450 MHz
keyboard:
/dev/input/event1 AT Translated Set 2 keyboard
mouse:
/dev/input/mice ImPS/2 Logitech Wheel Mouse
monitor:
Generic Monitor
graphics card:
Creative RIVA TNT2 Model 64/Model 64 Pro
S3 Integrated Trio3D
sound:
Crystal Audio
storage:
Floppy disk controller
Intel 82371AB/EB/MB PIIX4 IDE
network:
eth0 IBM 82557/8/9 [Ethernet Pro 100]
network interface:
eth0 Ethernet network interface
lo Loopback network interface
sit0 Network Interface
disk:
/dev/disk/by-id/ata-Maxtor_90644D3_A319P7SC Maxtor 90644D3
/dev/disk/by-id/ata-Maxtor_90644D3_A319P74C Maxtor 90644D3
partition:
/dev/disk/by-id/ata-Maxtor_90644D3_A319P7SC-part1 Partition
/dev/disk/by-id/ata-Maxtor_90644D3_A319P74C-part1 Partition
/dev/disk/by-id/ata-Maxtor_90644D3_A319P74C-part2 Partition
/dev/disk/by-id/ata-Maxtor_90644D3_A319P74C-part3 Partition
cdrom:
/dev/disk/by-path/pci-0000:00:02.1-ide-0:1 TOSHIBA CD-ROM XM-6402B
floppy:
/dev/fd0 Floppy Disk
usb controller:
Intel 82371AB/EB/MB PIIX4 USB
bios:
BIOS
bridge:
Intel 440BX/ZX/DX - 82443BX/ZX/DX Host bridge
Intel 440BX/ZX/DX - 82443BX/ZX/DX AGP bridge
Intel 82371AB/EB/MB PIIX4 ISA
Intel 82371AB/EB/MB PIIX4 ACPI
hub:
Linux 2.6.13-15.8-default uhci_hcd UHCI Host
Controller
memory:
Main Memory
unknown:
FPU
DMA controller
PIC
Timer
RTC
Keyboard controller
/dev/lp0 Parallel controller
PS/2 Controller
PnP Unclassified device
PnP Unclassified device
PnP Unclassified device
PnP Unclassified device
PnP Unclassified device
PnP Unclassified device
PnP Unclassified device
PnP Unclassified device
PnP Unclassified device
PnP Unclassified device
PnP Unclassified device
PnP Unclassified device
PnP Unclassified device
PnP Unclassified device
Crystal Audio
Crystal Audio
/dev/ttyS0 16550A
/dev/ttyS1 16550A



Al