HighDots.NET Computer Hardware Forums  

Hard drive capacity, etc.

PC Storage Devices Hard drives & other PC storage devices discussions (comp.sys.ibm.pc.hardware.storage)


Discuss Hard drive capacity, etc. in the PC Storage Devices forum.



Reply
 
Thread Tools Search this Thread Display Modes
  #11  
Old   
Arno Wagner
 
Posts: n/a

Default Re: Hard drive capacity, etc. - 05-22-2007 , 12:56 AM






Previously Howard Kaikow <kaikow (AT) standards (DOT) com> wrote:
Quote:
"Eric Gisin" <gisin (AT) uniserve (DOT) com> wrote in message
news:1179705034.770441 (AT) netadmin1 (DOT) interbaun.net...
None for the chipset. Check the BIOS date: 1997 -> 32GB, 1999 -> 128GB.
If you set the drive type to NONE, Windows will use IDE driver limit.

My sister has the same PC, except I use SCSI and have a more recentBIOS.

When she got the system, it came with a 14.4GB Ultra DMA/33 drive.
So tlhe limit would be higher than 8.4GB
You cannot tell the BIOS limit this way, since the SCSI controller has
its own BIOS with a, usually, prettu high limit. Typically 2TB or
higher, since SCSI uses at least 32 address bits.

Quote:
Later, I had her buy a 40GB Maxtor, along with a Promise controller to get
the full speed.
The controller would again have its own BIOS and Promise supports
LBA48 in its newer BIOS revisions.

Arno



Reply With Quote
  #12  
Old   
Howard Kaikow
 
Posts: n/a

Default Re: Hard drive capacity, etc. - 05-22-2007 , 06:33 AM






"Eric Gisin" <gisin (AT) uniserve (DOT) com> wrote

Quote:
I've tried this a few times with different systems with mixed results.
Often a computer will
insist on booting from the IDE drive even if you tell it explicitly not
to in the BIOS.

Not an issue if you don't activate any partition, or make them all
logical, or set drive type to
NONE.
Sounds right to me.
I do not know how to set drive type to NONE, but I would not activate any
parturition, and some would be Linux partitions.




Reply With Quote
  #13  
Old   
Howard Kaikow
 
Posts: n/a

Default Re: Hard drive capacity, etc. - 05-22-2007 , 06:35 AM



"Arno Wagner" <me (AT) privacy (DOT) net> wrote

Quote:
My sister has the same PC, except I use SCSI and have a more recentBIOS.

When she got the system, it came with a 14.4GB Ultra DMA/33 drive.
So tlhe limit would be higher than 8.4GB

You cannot tell the BIOS limit this way, since the SCSI controller has
its own BIOS with a, usually, prettu high limit. Typically 2TB or
higher, since SCSI uses at least 32 address bits.
My sister's drive is not SCSI.




Reply With Quote
  #14  
Old   
Arno Wagner
 
Posts: n/a

Default Re: Hard drive capacity, etc. - 05-22-2007 , 07:11 AM



Previously Howard Kaikow <kaikow (AT) standards (DOT) com> wrote:
Quote:
"Arno Wagner" <me (AT) privacy (DOT) net> wrote in message
news:5bfevuF2slu5lU1 (AT) mid (DOT) individual.net...
My sister has the same PC, except I use SCSI and have a more recentBIOS.

When she got the system, it came with a 14.4GB Ultra DMA/33 drive.
So tlhe limit would be higher than 8.4GB

You cannot tell the BIOS limit this way, since the SCSI controller has
its own BIOS with a, usually, prettu high limit. Typically 2TB or
higher, since SCSI uses at least 32 address bits.

My sister's drive is not SCSI.
But it is on an IDE controller card with its own BIOS. If the card's
BIOS is current, then it supports LBA48, i.e. up to 140TB.

Arno


Reply With Quote
  #15  
Old   
Spam Bob
 
Posts: n/a

Default Re: Hard drive capacity, etc. - 05-22-2007 , 09:57 AM



Howard Kaikow wrote:
Quote:
"Eric Gisin" <gisin (AT) uniserve (DOT) com> wrote in message
news:1179790778.126195 (AT) netadmin1 (DOT) interbaun.net...
I've tried this a few times with different systems with mixed results.
Often a computer will
insist on booting from the IDE drive even if you tell it explicitly not
to in the BIOS.
Not an issue if you don't activate any partition, or make them all
logical, or set drive type to
NONE.

Sounds right to me.
I do not know how to set drive type to NONE, but I would not activate any
parturition, and some would be Linux partitions.
Certainly doesn't hurt to give it a shot. I disagree with Eric's
statement, at least in part. I've never tried setting the drive type to
NONE (sounds promising), but his other other suggestions don't guarantee
success in my experience (but they are worth trying). Go into the
system BIOS and change the drive setting from AUTO to NONE.


Reply With Quote
Reply




Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

vB code is On
Smilies are On
[IMG] code is On
HTML code is Off



Powered by vBulletin Version 3.5.3
Copyright ©2000 - 2008, Jelsoft Enterprises Ltd.